Huawei SUN2000-2KTL-L1 Скачать руководство пользователя страница 97

Страница: 97 / 122

Alarm

Alarm Name

Alarm

Severity

Possible Causes

Troubleshooting

2065

Upgrade Failed

or Version

Mismatch

Minor

The upgrade does not

complete normally.
Cause ID = 1–4, 7
● 1. The software and

hardware of the main

controller do not match.

● 2: The main and

auxiliary controller

software versions do not

match.

● 3: The monitoring and

power controller

software versions do not

match.

● 4: The upgrade fails.
● 7: The optimizer

upgrade fails.

1. Perform an upgrade

again.

2. If the upgrade fails for

multiple times, contact

your dealer or Huawei

technical support.

61440

Monitoring

Unit Faulty

Minor

Cause ID = 1
● The flash memory is

insufficient.

● The flash memory has

bad sectors.

Turn off the AC output

switch and DC input switch,

and then turn them on

after 5 minutes. If the fault

persists, replace the

monitoring board or

contact your dealer Huawei

technical support.

2067

Faulty Power

Collector

Major

Cause ID = 1
The smart power sensor is

disconnected.

1. Check that the

configured power meter

model is the same as

the actual model.

2. Check that the

communications

parameters for the

smart power sensors are

the same as the

SUN2000 RS485

configurations.

3. Check whether the

smart power sensor is

powered on and

whether the RS485

communications cable is

connected.

SUN2000-(2KTL-6KTL)-L1

User Manual

8 System Maintenance

Issue 04 (2021-04-01)

Содержание SUN2000-2KTL-L1



























































































































Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы:

Huawei SUN2000-2KTL-L1, Руководство пользователя, Страница: 97 / 122

Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы: