Huawei SUN2000-2KTL-L1 Скачать руководство пользователя страница 76

Страница: 76 / 122

Parameter Name

Description

Communication

disconnection

detection time

Specifies the time for determining the

communication disconnection

between the SUN2000 and the

Dongle.
This parameter is displayed when

Communication disconnection fail-

safe is set to Enable.

Grid connection

with limited power

(%)

Closed-loop controller

● If multiple SUN2000s are

cascaded, set this parameter to

SDongle/SmartLogger.

● If there is only one SUN2000, set

this parameter to Inverter.

Limitation mode

Total power indicates export

limitation of the total power at the

grid-tied point.

PV plant capacity

Specifies the total maximum active

power in the SUN2000 cascading

scenario.

Maximum grid feed-in

power

Specifies the percentage of the

maximum active power of the grid-

tied point to the PV plant capacity.

Power adjustment

period

Specifies the shortest interval for a

single anti-backfeeding adjustment.

Power control

hysteresis

Specifies the dead zone for adjusting

the SUN2000 output power. If the

power fluctuation is within the power

control hysteresis, the power is not

adjusted.

Active power output

limit for fail-safe

Specifies the derating value of the

SUN2000 active power by percentage.

If the Smart Dongle does not detect

any meter data or the

communication between the Smart

Dongle and the SUN2000 is

disconnected, the Smart Dongle

delivers the derating value of the

SUN2000 active power by percentage.

SUN2000-(2KTL-6KTL)-L1

User Manual

7 Man-Machine Interaction

Issue 04 (2021-04-01)

Содержание SUN2000-2KTL-L1



























































































































Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы:

Huawei SUN2000-2KTL-L1, Руководство пользователя, Страница: 76 / 122

Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы: