Huawei SUN2000-2KTL-L1 Скачать руководство пользователя страница 31

Страница: 31 / 122

4.5.1 Wall-Mounted Installation

Procedure

Step 1 Determine the positions for drilling holes using the marking-off template. Level

the positions of mounting holes using a level, and mark the positions with a

marker.

Step 2 Secure the mounting bracket.

D ANGER

When drilling holes, avoid the water pipes and power cables buried in the wall.

NO TE

M6x60 expansion bolts are delivered with the SUN2000. If the length and amount of the

bolts do not meet installation requirements, prepare M6 stainless steel expansion bolts by

yourself.

Figure 4-8 Expansion bolt composition

(1) Bolt

(2) Nut

(3) Spring washer

(4) Flat washer

(5) Expansion sleeve

NO TICE

● To prevent dust inhalation or contact with eyes, wear safety goggles and an

anti-dust mask when drilling holes.

● Wipe away any dust in or around the holes and measure the hole distances. If

the holes are inaccurately positioned, drill holes again.

● Level the head of the expansion sleeve with the concrete wall after removing

the nut, spring washer, and flat washer. Otherwise, the mounting bracket will

not be securely installed on the wall.

● Loosen the nut, spring washer, and flat washer of the expansion bolt at the

bottom.

SUN2000-(2KTL-6KTL)-L1

User Manual

4 System Installation

Issue 04 (2021-04-01)

Содержание SUN2000-2KTL-L1



























































































































Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы:

Huawei SUN2000-2KTL-L1, Руководство пользователя, Страница: 31 / 122

Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы: