Huawei SUN2000-2KTL-L1 Скачать руководство пользователя страница 67

Страница: 67 / 122

Category

Status

Description

Steady red

Fault.

Communication

indicator

LED3

–

Blinking green at short intervals (on for 0.2s and

then off for 0.2s)

Communication is in

progress.

Blinking green at long intervals (on for 1s and

then off for 1s)

The mobile phone is

connected to the

SUN2000.

Off

There is no

communication.

NO TE

If the off-grid load is overloaded, indicators LED1 and LED2 on the inverter blink orange

slowly. Reduce the off-grid load power and manually clear the alarm or until the inverter is

recovered. The inverter attempts to restart at an interval of 5 minutes. If the inverter fails to

restart for three times, the interval changes to 2 hours. If the inverter is standby in off-grid

mode, check the inverter alarms and rectify the fault.

Table 6-3 LED indicators 2

Category

Status

Description

Device

replacement

indication

LED1

LED2

LED3

–

Steady red

The SUN2000 hardware

is faulty. The SUN2000

needs to be replaced.

----End

SUN2000-(2KTL-6KTL)-L1

User Manual

6 System Commissioning

Issue 04 (2021-04-01)

Содержание SUN2000-2KTL-L1



























































































































Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы:

Huawei SUN2000-2KTL-L1, Руководство пользователя, Страница: 67 / 122

Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы: