Huawei SUN2000-2KTL-L1 Скачать руководство пользователя страница 26

Страница: 26 / 122

Type

Tools and Instruments

Marker

Steel measuring tape

Level

Hydraulic pliers

Heat-shrink tubing

Heat gun

Personal protective

equipment (PPE)

Safety gloves

Safety goggles

Anti-dust mask

Safety boots

4.3 Determining the Installation Position

Basic Requirements

●

The SUN2000 is protected to IP65 and can be installed indoors or outdoors.

●

Do not install the SUN2000 in a place where personnel are easy to come into

contact with its enclosure and heat sink, because these parts are extremely

hot during operation.

●

Do not install the SUN2000 near flammable or explosive materials.

●

Do not install the SUN2000 at a place within children's reach.

●

The SUN2000 will be corroded in salt areas, and the salt corrosion may cause

fire. Do not install the SUN2000 outdoors in salt areas. A salt area refers to

the region within 500 meters from the coast or prone to sea breeze. The

regions prone to sea breeze vary with weather conditions (such as typhoons

and monsoons) or terrains (such as dams and hills).

SUN2000-(2KTL-6KTL)-L1

User Manual

4 System Installation

Issue 04 (2021-04-01)

Содержание SUN2000-2KTL-L1



























































































































Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы:

Huawei SUN2000-2KTL-L1, Руководство пользователя, Страница: 26 / 122

Результаты поиска

Содержание SUN2000-2KTL-L1

Отзывы: