Huawei FusionModule1000A Скачать руководство пользователя | Manualshive

Страница: 59 / 108

background image

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

8 Installing Devices Inside Pre-fab. Modules

Issue 03 (2020-06-09)

Copyright © Huawei Technologies Co., Ltd.

52

8.1.2 Installing Batteries

Prerequisites

The pre-fab. modules have been installed.

Precautions



To ensure personal safety, unpack, move, and install batteries by following the
instructions in the manuals delivered with the batteries.



Except for necessary functional parts, wrap the exposed metal parts of tools such as
screwdrivers and wrenches with at least two layers of insulation tape.



Wrap the OT terminal of a cable with insulation tape, and remove the tape when the
cable is placed in position and the terminal to be connected is confirmed.



Leave one break point disconnected when connecting batteries at each layer, and connect
the break point on each layer after other cables are connected.



Tighten screws to prevent sparks generated upon power-on.



Only qualified technicians can connect battery cables.



Ensure that all the safety measures have been taken before installation.



Ensure that the circuit breakers in the battery circuit breaker (BCB) box are OFF when
installing batteries.



Never short-circuit the two poles of a battery when handling or installing batteries.

Preparations

Tools: Phillips screwdriver, pallet truck, adjustable wrench, protective gloves

Materials: insulation tape, battery, copper bar or cable

Documents: battery wiring diagram, documents delivered with the batteries

Skill requirement: personnel qualified for installing batteries

For the diagram, see the quick installation guide for the solution in use.

Procedure

Step 1

Use a pallet truck to move batteries to a position near the pre-fab. module door closest to the
installation position.

Step 2

Unpack the batteries.

Step 3

Open the front door of the battery cabinet.

Due to space limitation, connect power cables after placing batteries on one layer.

Step 4

Place batteries in the battery cabinet from bottom to top and from left to right.

«
...
57
58
59
60
61
...
»

Содержание FusionModule1000A













































































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule1000A

Бренд: kincrome Страницы: 2

Бренд: MCE Technologies Страницы: 9

Бренд: SmartStore Страницы: 16

AssuredSAN 4544

Бренд: Dot Hill Systems Страницы: 100

TotalStorage NAS 100

Бренд: IBM Страницы: 18

Cheetah 15K.7 FC

Бренд: Seagate Страницы: 90

Бренд: HOLZMANN MASCHINEN Страницы: 18

2.5-INCH Travelstar HTS542525K9A300

Бренд: Hitachi Страницы: 2

2.5-INCH Travelstar HTS542525K9A300

Бренд: Hitachi Страницы: 5

2.5-Inch Mobile 7200 RPM 9.5mm Travelstar HTS727575A9E364

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 82

Бренд: Hitachi Страницы: 137

3.5-INCH Deskstar HDP725050GLAT80

Бренд: Hitachi Страницы: 2

3.5-inch Deskstar HDS721010DLE630

Бренд: Hitachi Страницы: 2

3.5-Inch Desktop 7200 RPM Deskstar HDS721010CLA332

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 135

2.5-INCH Travelstar HTS542525K9A300

Бренд: Hitachi Страницы: 171

Бренд: Hitachi Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды