Huawei FusionModule1000A Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 108

background image

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

About This Document

Issue 03 (2020-06-09)

Copyright © Huawei Technologies Co., Ltd.

ii

About This Document

Purpose

This document describes the site requirements for installing the FusionModule1000A
prefabricated all-in-one data center (FusionModule1000A for short) as well as the methods
and skills required for installing pre-fab. modules, pipes, and cables, providing installation
guidance and technical support for onsite installation personnel and technical support
engineers.

Intended Audience

This document is intended for:



Hardware installation engineers



Technical support engineers



Commissioning engineers



Maintenance engineers

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Remarks

Indicates a hazard with a high level of risk which, if not
avoided, will result in death or serious injury.

Indicates a hazard with a medium level of risk which, if
not avoided, could result in death or serious injury.

Indicates a hazard with a low level of risk which, if not
avoided, could result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.

NOTICE is used to address practices not related to
personal injury.

«
1
2
3
4
5
...
»

Содержание FusionModule1000A













































































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule1000A

Бренд: Oki Страницы: 16

Бренд: Seville Classics Страницы: 2

Бренд: Quantum Страницы: 78

StoraXe PowerBooster GSS0608

Бренд: ADS-tec Страницы: 140

Quick Framer Gambrel Roof

Бренд: G&T SALES Страницы: 5

Бренд: Duratuf Страницы: 16

DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116

Бренд: USP Страницы: 79

EonStor A12E-G2121

Бренд: Infortrend Страницы: 7

Бренд: Magnusson Страницы: 18

StoreVirtual 3200

Бренд: HPE Страницы: 54

Бренд: HOMEDEPOT Страницы: 24

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Бренд: LaCie Страницы: 74

Бренд: DataDirect Networks Страницы: 118

Бренд: AEG Страницы: 16

Post-Type Wall Mount Shelving

Бренд: Omega Страницы: 4

Бренд: Freecom Страницы: 2

Бренд: Aluratek Страницы: 1

Бренд: Alpha ESS Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды