Huawei FusionModule 1000A40 Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 199

background image

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

6 Emergency Operations

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

177

6

Emergency Operations

6.1 Emergency Operations for Mains Failure

Prerequisites

The mains supply to the FusionModule1000 is faulty.

Context

The FusionModule1000 power supply and distribution system supports the following power
supply modes:



One mains supply and one DG



Two mains supplies

Perform emergency operations based on the power supply mode used by the FusionModule1000.

Procedure

Step 1

Check whether the UPS is working properly.

Step 2

Check whether the ATS in the mains bus coupler cabinet switches to the other mains supply
or the DG.



If the switchover fails, manually start the DG within 5 minutes after the power outage
occurs. If the DG still cannot be started, back up data immediately.



If the DG starts and supplies power normally, find the cause of the power outage and the
DG backup time as soon as possible. If the DG can supply power until the mains supply is
restored, prepare for the subsequent power supply switchover. If the power provided by
the DG cannot sustain to the time the mains supply is restored, back up the data
immediately.



If the ATS switchover is working properly, check whether all devices are working
properly.

«
...
183
184
185
186
187
...
»

Содержание FusionModule 1000A40








































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule 1000A40

Бренд: NEC Страницы: 54

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: Vahle Страницы: 96

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: Xiitech Страницы: 6

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

Бренд: Oakworks Medical Страницы: 28

Бренд: OHAUS Страницы: 84

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: Tadano Страницы: 402

Бренд: Balanced Body Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды