Huawei FusionModule 1000A40 Скачать руководство пользователя страница 63

Страница: 63 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

4 Alarms and Faults

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

4.11 Access Alarm

Fault
Category

Alar
m
Sever
ity

Symptom

Possible
Cause

Troubleshooting

Access
alarm

Critica
l

The door status
cannot be controlled.

The access
controller is
faulty.

Verify the access
controller cable
connections, or replace
the access controller.

The access card
cannot be read.

The access card
is damaged.

Prepare a new access
card and assign the
access permission.

The card reader
is faulty.

Verify the card reader
cable connections, or
replace the end door card
reader.

4.12 Water Intrusion Alarm

Fault
Category

Alar
m
Sever
ity

Symptom

Possible
Cause

Troubleshooting

Water
Intrusion
Alarm

Gener
al

There is no water
onsite.

The water
sensor is faulty.

Replace the water sensor
(point type).

There is water
onsite.

A pipe is
damaged.

Contact Huawei
technical support.

A humidity
water refill pipe
is damaged.

Replace the humidifier
water refill pipe for a
precision air conditioner.

The condensate
drainpipe is
damaged.

Replace the condensate
drainpipe of a precision
air conditioner.

The condensate
drainpipe is
blocked.

Remove the drainpipe
outside the pre-fab.
module, and dig out the
material blocking the
pipe using a thin iron
wire.

Содержание FusionModule 1000A40








































































































































































































Результаты поиска

Содержание FusionModule 1000A40

Отзывы:

Похожие инструкции для FusionModule 1000A40

Бренды по названию

Популярные бренды

Huawei FusionModule 1000A40, Руководство по обслуживанию

Результаты поиска

Содержание FusionModule 1000A40

Отзывы:

Похожие инструкции для FusionModule 1000A40

Бренды по названию

Популярные бренды