HSM FP 1500 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 56

HSM FP 1500 Скачать руководство пользователя страница 38

Maintenance

FP 1500

FP 3000

6.817.999.520

Edition 03/2000

8 - 4

➪

Switch the main switch on.

Risk of squeezing

Do not reach into the unprotected parts of the barrel press while the
covers are removed.

➪

Move the press ram up and down several times and check the oil level again with
the press ram in the upper position (see Section 8.2).

➪

Top up oil as necessary.

➪

Screw the venting filter back on.

➪

Screw the rear cover back on.

If you use an oil sucton aggregate, proceed accordingly as per the above description.

8.4

Cleaning the hydraulic oil tank

➪

Drain oil (see Section 8.3).

➪

Unscrew the hexagon screws on the tank cover using an open-end spanner SW
13 and remove the tank cover and the seal.

➪

Clean the inside of the hydraulic oil tank, remove and dispose of any oil sludge.

➪

Screw the oil drainage screw back on together with a new copper ring seal.

➪

Replace the tank cover seal and install the tank cover.

«
...
36
37
38
39
40
...
»

Содержание FP 1500

























































Отзывы:

Нет отзывов