HPE ProLiant DL20 Скачать руководство пользователя страница 68

Страница: 68 / 109

22.

Install all components removed from the failed system board.

23.

Connect all cables disconnected from the failed system board.

24.

Install the air baffle.

25.

Install the access panel.

26.

Do one of the following:

• Slide the server into the rack.
• Install the server into the rack.

27.

Connect each power cord to the server.

28.

Connect each power cord to the power source.

29.

Power up the server.

30.

If removed, install the security bezel.

After you replace the system board, you must re-enter the server serial number and product ID:

During the server startup sequence, press the

key to access UEFI System Utilities.

Select

System Configuration > BIOS/Platform Configuration (RBSU) > Advanced Options >

Advanced System ROM Options > Serial Number

, then press the

Enter

key.

Enter the serial number and press the

Enter

key. The following message appears:

The serial number should only be modified by qualified service personnel.

To clear the warning, press the

Enter

key.

Enter the serial number and press the

Enter

key.

Select

Product ID

. The following warning appears:

Warning: The Product ID should ONLY be modified by qualified service personnel. This value should
always match the Product ID located on the chassis.

Enter the product ID and press the

Enter

key.

To confirm exiting System Utilities, press the

F10

key.

The server will automatically reboot.

Removal and replacement procedures

Содержание ProLiant DL20














































































































Результаты поиска

Содержание ProLiant DL20

Отзывы:

Похожие инструкции для ProLiant DL20

Бренды по названию

Популярные бренды

HPE ProLiant DL20, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant DL20

Отзывы:

Похожие инструкции для ProLiant DL20

Бренды по названию

Популярные бренды