HPE ProLiant DL180 Скачать руководство пользователя страница 60

Страница: 60 / 172

Install the drive.

6. Determine the status of the drive from the drive LED definitions

The installation is complete.

Most current operating systems provide an NVMe SSD driver natively. Use this native (inbox) driver to
configure and deploy NVMe SSDs.

The SmartSSD Wear Gauge reports in the HPE Smart Storage Administrator contain information about
the current usage level and remaining expected lifetime of SSDs attached to the system. For more
information, see the

HPE Smart Array SR Gen10 Configuration Guide

at the

Hewlett Packard

Enterprise website

Drive cage options

The server supports the following drive cage options:

•

8-bay SFF drive cage

•

Rear 2-bay SFF drive cage

•

NVMe drive cage in the LFF chassis

•

NVMe-optical drive cage in the SFF chassis

The 8 LFF chassis can be upgraded to 12 LFF chassis with

8 to 12 upgrade option installed

Installing the 8-bay SFF drive cage

This option can be installed in boxes 1 and 2.

Prerequisites

Before you perform this procedure, make sure that you have a T-15 Torx screwdriver available.

Hardware options installation

Содержание ProLiant DL180













































































































































































Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды

HPE ProLiant DL180, Руководство пользователя

Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды