HPE ProLiant DL180 Скачать руководство пользователя страница 27

Страница: 27 / 172

Item LED

Status

Definition

Flashing green

The drive is doing one of the following:
• Rebuilding

• Performing a RAID migration

• Performing a stripe size migration

• Performing a capacity expansion

• Performing a logical drive extension

• Erasing

Flashing amber/
green

The drive is a member of one or more logical drives and predicts the
drive will fail.

Flashing amber The drive is not configured and predicts the drive will fail.

Solid amber

The drive has failed.

Off

The drive is not configured by a RAID controller.

Do not
remove

Solid white

Do not remove the drive. The drive must be ejected from the PCIe bus
prior to removal.

Flashing white

The drive ejection request is pending.

Off

The drive has been ejected.

Power

Solid green

Do not remove the drive. The drive must be ejected from the PCIe bus
prior to removal.

Flashing green

The drive ejection request is pending.

Off

The drive has been ejected.

NVMe SSD button actions

Component identification

Содержание ProLiant DL180













































































































































































Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды

HPE ProLiant DL180, Руководство пользователя

Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды