HPE ProLiant DL180 Скачать руководство пользователя страница 86

Страница: 86 / 172

15.

Connect each power cord to the server.

16.

Connect each power cord to the power source.

17. Power up the server

on page 43.

18.

If removed,

install the front bezel

The installation is complete.

Fan option

Fan population guidelines

The number of fans installed in the server determines fan redundancy.

Configuration

Fan
redundancy

Bay 1

Bay 2

Bay 3

Bay 4

Bay 5

Bay 6

One processor,
without NVMe drives
and rear 2-SFF
drives installed

Blank

Fan

One processor,
without NVMe drives
and rear 2-SFF
drives installed

Yes

Blank

Fan

Blank

Fan

One processor, with
NVMe drives or rear
2-SFF drives
installed

Blank

Fan

One processor, with
NVMe drives or rear
2-SFF drives
installed

Yes

Fan

Two processors

Blank

Fan

Two processors

Yes

Fan

Fan mode behavior

• In nonredundant fan mode, a fan failure or a missing fan causes:

◦ The system Health LED to flash amber.

◦ The operating system to orderly shutdown.

• In redundant fan mode:

◦ A fan rotor failure will switch the system to nonredundant fan mode.

This change is indicated by the Health LED flashing amber. The system continues to operate
normally in this mode.

◦ A second fan rotor failure or a missing fan causes the operating system to orderly shutdown.

Hardware options installation

Содержание ProLiant DL180













































































































































































Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды

HPE ProLiant DL180, Руководство пользователя

Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды