manualshive.com logo in svg

HP StorageWorks 7100 - Virtual Array, Приложение, Страница: 7 / 27

Поделиться
Скачать
HP StorageWorks 7100 - Virtual Array Скачать руководство пользователя страница 7

Event 

Number 

(dec/hex) 

Event 
Name 

Logged? 

Predictive 

Maintenance 

Implication 

Suspected 
Components 

Mf

g Fail? 

Description 

for LUN operation. 

controllers to complete the requested LUN 
operation.  More memory must be installed before 
the requested operation can be completed 
successfully. 

89/0x59 

Undefined 

N 

N.A. 

None 

N 

Undefined event code. 

90/0x5a 

Host Read Collision With 
Failed Cache Post 

Y 

ignore - see 

accompanying 

errors 

None 

N 

A host write was flushed from cache but ended with 
a non-SUCCESS status; this caused cache to mark 
the write cache entry as RETRY which means it is 
stuck in cache. A new host read partially hits the 
same address which normally causes the write to 
flush but the write is stuck in cache.  The response is 
to fail the read. 

91/0x5b 

Ambiguous Volume Set 
Reference 

Y 

ignore - operator 

error 

None 

Y 

A volume set ID referenced in a recover command 
was ambiguous.  If a null (wild card) volume set 
was used in a recover command then this error 
means that the controller found drives from multiple 
volume sets present.  If a non-null volume set uas 
used then this error means that the contoller is 
already attached to a volume set other than the one 
referenced in the recover command. 

92/0x5c 

Recovery From RAM Loss 
Failed 

Y Single 

Occurrance 

Disk Drive, 
Disk Interface, 
Controller, 
Operator 

Y 

This error indicates that the controller was unable to 
recover an NVRAM image from any disk in the 
volume set.  This could be because none of the disks 
present have images, or the disks that did have 
images were removed, or failed before the images 
could be fully uploaded into the controller. 

93/0x5d 

Multiple Failures Suspected 
During Recovery 

Y 

ignore - see 

accompanying 

errors 

None 

Y 

Conditions detected during recovery indicate that at 
least one failure or hot plug event occurred in 
addition to the loss of NVRAM that prompted the 
recovery.  This implies that data integrity is likely to 
have been compromised in ways that are not 
detectable outside of the occurrance of this log entry 
or sense data report.  It is likely that the controller 
does not have sufficient information to determine 
the extent of the damage. 

94/0x5e 

Volume Set Missing During 
Recovery 

Y 

ignore - operator 

error 

None 

Y 

The volume set referenced in a recover command is 
not present in the subsystem.  If a NULL volume set 
was referenced then this error indicates that no 
members of any volume set were present.  This error 
can also result from imcompatible stamp versions 

95/0x5f 

RAM Configuration Mismatch 
During Recovery 

Y Single 

Occurrance 

Controller 
SIMM, operator 
error 

Y 

An attempt was made to recover an image after 
RAM loss but the image would not fit in the non-
failing memory available on the controller.  Either 
the SIMM configuration has been modified, or one 
or more SIMMs have failed.  Recovery may be 
possible using the another controller as the primary. 

96/0x60 

Read Recovered With RAID 5 
Retries 

Y 

Ignore - See 

accompanying 

errors 

None 

N 

Retries were used by the R5 module in the 
successful completion of a read. 

97/0x61 

Write Recovered With RAID 5 
Retries 

Y 

Ignore - See 

accompanying 

errors 

None 

N 

Retries were used by the R5 module in the 
successful completion of a write. 

98/0x62 

Read Recovered With RAID 5 
Redundancy 

Y 

Ignore - See 

accompanying 

errors 

None 

N 

Redundancy was used by the R5 module in the 
successful completion of a read. 

99/0x63 

Write Recovered With RAID 5 
Redundancy 

Y 

Ignore - See 

accompanying 

errors 

None 

N 

Redundancy was used by the R5 module in the 
successful completion of a write. 

100/0x64 

Read Recovered With RAID 1 
Redundancy 

Y 

Ignore - See 

Accompanying 

Errors 

None 

N 

Redundancy was used by the R1 module in the 
successful completion of a read. 

101/0x65 

Write Recovered With RAID 1 
Redundancy 

Y 

Ignore - See 

Accompanying 

Errors 

None 

N 

Redundancy was used by the R1 module in the 
successful completion of a write. 

102/0x66 

Disk drive reported a SMART 
event  

Y Signals 

internal 

drive errors 

threshold 

exceeded, 

Disk Drive 

Y 

The disk drive reported a SMART event.  The event 
is logged and the common sense data is updated for 
all regular read/write and passthru commands.  The 
precedence for SMART event data in the common 
area is low, so that other errors that occur during the 
same I/O are reported back to the host.  A SMART 
event does not affect the I/O except that it does 

Содержание StorageWorks 7100 - Virtual Array




























Отзывы:

Нет отзывов