manualshive.com logo in svg

HP StorageWorks 7100 - Virtual Array, Приложение, Страница: 25 / 27

Поделиться
Скачать
HP StorageWorks 7100 - Virtual Array Скачать руководство пользователя страница 25

Event 

Number 

(dec/hex) 

Event 
Name 

Logged? 

Predictive 

Maintenance 

Implication 

Suspected 
Components 

Mf

g Fail? 

Description 

520/0x208 

The over temperature error bit 
is set 

Y 

 

Power Supply 

Y 

The over current error bit is set in the power supply 
expander  

521/0x209 

The under voltage error bit is 
set 

Y 

 

Power Supply 

Y 

The under voltage error bit is set in the power 
supply expander  

522/0x20a 

Dram text area cksum error 

Y 

 

Controller 

Y 

The DRAM Text area checksum does not match the 
checksum calculated during initialization. A bgm 
timer polls to check the CKSUM once every hour.  

523/0x20b 

Software address warning 

Y 

 

Controller 

N 

This warning indicates that there is switch conflict 
in the JBOD enclosures. Two or more enclosure 
switches are set to the same address.   

524/0x20c 

LCC switch address warning 

Y 

 

Controller 

N 

This warning indicates that there is an LCC switch 
mismatch within a JBOD enclosures.   

525/0x20d 

Power supply not present 

Y 

 

Power Supply 

Y 

This warning indicates that the power supply is not 
present  

526/0x20e 

Map Disk Event 

Y 

 

Controller 

N 

This error code indicates that the Topology Manager 
MAP DISK code had an event that it has logged. 
The defined events are REDUNDANT MAP 
DISKS, MAP_DISK_REDUNDANCY_LOSS, and 
NO_MAP_DISKS. 

527/0x20f 

Battery NVRAM backup 
command 

Y  NVRAM 

battery charger 

N 

The command sent to enable or disable the batteries 
from backing up the NVRAM has failed. 

528/0x210 

Unsupported host port behavior 
table revision 

Y 

Ignore 

None 

N 

The host port behavior table that was read from 
chassis NV memory contains an unsupported 
revision value.  The RAM-based table will be 
initialized as empty. 

529/0x211 

Host Port Behavior table was 
initialized as empty 

Y 

 

None 

N 

The host port behavior table was initialized as 
empty due to a failure to read the contents from 
chassis NV storage. 

530/0x212 

Firmware download failed 

Y 

Ignore.  These 

should be 

detected by the 

download utility. 

none 

N 

A firmware download operation failed.  The details 
of the failure are included in the event unique 
section of the event and other events logged in 
conjunction with this one. 

531/0x213 

AutoFormat Event Occured 

Y 

Ignore unless no 

Operator activity 

Disk Drive, 
Back End FC 
Link 

N 

An AutoFormat event was logged, this is caused 
either by a backend format of an internal drive 
beginning or completing.  Look as the associated 
data for drive and status. 

532/0x214 

Power supply is not connected 
to an AC source 

Y 

 

Power Supply 

Y 

This warning indicates that the power supply is not 
connected to an AC source. 

533/0x215 

Some non-critical midplane 
eeprom data was not restored. 

Y  Midplane 

EEPROM 

N 

This warning indicates that some non-critical 
eeprom data was not restored during the automatic 
restore process.  The user should be able to replace 
this data by hand.  (Licenses, mode parms, Host port 
behavior, etc. 

534/0x216 

Automatic midplane repair 
failed. 

Y  Midplane 

EEPROM 

Y 

This warning indicates the automatic midplane 
eeprom repair process has failed because of bad 
NVSRAM data.  The repair can not be done. 

535/0x217 

Temp sensor exceeded warning 
temperature. 

Y  Controller 

Temp Sensor 

Y 

The temperature sensor has exceeded the 
recommended temperature for asserting an over-
temp warning. 

536/0x218 

Temp sensor exceeded 
shutdown temperature. 

Y  Controller 

Temp Sensor 

Y 

The temperature sensor has exceeded the 
recommended temperature for issuing a controller 
shutdown. 

537/0x219 

Temp sensor is now in range. 

Y 

 

Controller 
Temp Sensor 

N 

The temperature sensor had exceeded the 
recommended temperature for asserting a warning.  
The temperature has now come back down within 
range.  There is 3 degrees C of hysteresis. 

538/0x21a 

Disk interface online. 

Y 

Ignore 

Disk interface 

N 

A disk interface has come online and is functional.  
This occurs normally during reset or reconfiguration 
(hotplug). 

539/0x21b 

Disk interface device 
discovered. 

Y 

Ignore 

Disk interface 

N 

A device has been discovered on a disk interface 
during reset or reconfiguration (hotplug).  This is 
normal. 

540/0x21c 

Disk interface device logout 

Y 

Ignore 

Disk Interface 

N 

The login to a device on a disk interface has been 
closed.  This occurs normally during reconfiguration 
(hotplug). 

541/0x21d 

Disk interface error count has 
incremented 

Y Ignore, 

unless 

occurring 

frequently 

Disk interface 

N 

The count of link-level errors on a disk interface has 
incremented.  This can occur under normal 
circumstances (especially with disk hotplug), so it 
does not indicate a problem unless it occurs 
frequently. 

Содержание StorageWorks 7100 - Virtual Array




























Отзывы:

Нет отзывов