manualshive.com logo in svg

HP Rp5000 - Point of Sale System, Руководство по устранению неисправностей

Поделиться
Скачать
HP Rp5000 - Point of Sale System Скачать руководство пользователя страница 68

A–14

www.hp.com

Troubleshooting Guide

POST Error Messages

Red Power LED 
flashes four 
times, once 
every second, 
followed by a 
two-second 
pause.

None

Power failure 
(power supply is 
overloaded).

1. Check that the voltage selector, 

located on the rear of the power 
supply, is set to the appropriate 
voltage. Proper voltage setting 
depends on your region.

2. Open the hood and ensure the 

4-wire power supply cable is 
seated into the connector on the 
system board.

3. Check if a device is causing the 

problem by removing ALL attached 
devices (such as hard, diskette, or 
optical drives, and expansion 
cards). Power on the system. If the 
system enters the POST, then power 
off and replace one device at a 
time and repeat this procedure until 
failure occurs. Replace the device 
that is causing the failure. Continue 
adding devices one at a time to 
ensure all devices are functioning 
properly.

4. Replace the power supply.

5. Replace the system board.

Red Power LED 
flashes five 
times, once 
every second, 
followed by a 
two-second 
pause.

5

Pre-video  memory 
error

1. Reseat DIMMs. Power on the 

system.

2. Replace DIMMs one at a time to 

isolate the faulty module.

3. Replace third-party memory with 

HP memory.

4. Replace the system board.

Diagnostic Front Panel LEDs and Audible Codes 

(Continued)

Activity

Beeps

Possible Cause

Recommended Action

Содержание Rp5000 - Point of Sale System















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды