HP Rp5000 - Point of Sale System Скачать руководство пользователя страница 24

Страница: 24 / 78

2–8

www.hp.com

Troubleshooting Guide

Troubleshooting Without Diagnostics

Solving Power Supply Problems

Problem

Cause

Solution

Power supply shuts down
intermittently.

Voltage selector switch
on rear of computer
chassis not switched to
correct line voltage
(115V or 230V).

Select the proper AC voltage using
the selector switch.

Power supply will not
turn on because of
internal power supply
fault.

Contact an authorized service
provider to replace the power
supply.

Computer powered off
automatically and the
Power LED flashes Red two
times, once every second,
followed by a two-second
pause.

Processor thermal
protection activated:
A fan may be blocked
or not turning.
OR
The heatsink/fan
assembly is not
properly attached to the
processor.

1. Ensure that the computer air

vents are not blocked and the
processor cooling fan is
running.

2. Open hood, press the power

button, and see if the processor
fan spins. If the processor fan is
not spinning, make sure the
fan's cable is plugged onto the
system board header. Ensure
the fan is fully/properly seated
or installed.

3. If fan is plugged in and seated

properly, but is not spinning,
then replace the processor fan.

4. Reseat processor heatsink and

verify that the fan assembly is
properly attached.

5. Contact an authorized reseller

or service provider.

Содержание Rp5000 - Point of Sale System















































































Результаты поиска

Содержание Rp5000 - Point of Sale System

Отзывы:

Бренды по названию

Популярные бренды

HP Rp5000 - Point of Sale System, Руководство по устранению неисправностей

Результаты поиска

Содержание Rp5000 - Point of Sale System

Отзывы:

Бренды по названию

Популярные бренды