manualshive.com logo in svg

HP Rp5000 - Point of Sale System, Руководство по устранению неисправностей

Поделиться
Скачать
HP Rp5000 - Point of Sale System Скачать руководство пользователя страница 64

A–10

www.hp.com

Troubleshooting Guide

POST Error Messages

1782-Disk Controller 
Failure

Hard drive circuitry 
error.

1. Run Computer Setup.

2. Clear CMOS. (See 

Appendix B, 

“Password Security and Resetting 
CMOS.”

)

3. Check cable seating/jumper settings.

4. Run hard drive diagnostics.

5. Disconnect additional drives.
6. Replace the hard drive.

7. Replace the system board.

1800-Tempera-

 

ture Alert

Internal temperature 
exceeds specification.

1. Check that computer air vents are not 

blocked and cooling fan is running.

2. Verify processor speed selection.

3. Replace the processor.

4. Replace the system board.

1801-Microcode 
Patch Error

Processor is not 
supported by 
ROM BIOS.

Upgrade BIOS to proper version.

Invalid Electronic 
Serial Number

Electronic serial number 
has become corrupted.

1. Run Computer Setup. If Setup already 

has data in the field or will not allow 
the serial number to be entered, 
download from 

www.hp.com

 

and run SP5572.EXE (SNZERO.EXE).

2. Run Computer

 

Setup and try to enter 

serial number under Security, System 
IDs, then save changes.

ECC Multiple Bit 
Error Detected in 
Memory Module

Chipset has detected 
more than one bad bit 
in a 64-bit quadword of 
the memory array.

Replace the memory module.

Parity Check 2

Parity RAM failure.

Run Computer Setup and Diagnostic 
utilities.

Numeric Codes and Text Messages 

(Continued)

Code/Message

Probable Cause

Recommended Action

Содержание Rp5000 - Point of Sale System















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды