HP ProLiant XL270d Gen9 Скачать руководство пользователя страница 54

Страница: 54 / 126

13.

Install the server into the chassis.

14.

Connect all peripheral cables to the server .

15.

Power up the server .

Replacing the GPU accelerator power cables

NOTE:

This procedure is not applicable to NVIDIA Tesla P4 GPU.

NVIDIA Tesla P4 GPU does not have any power cables

Procedure

Back up all server data.

Power down the server

Disconnect all peripheral cables from the server front panel.

Remove the server from the chassis

Place the server on a sturdy, level surface.

Remove the side panel

Remove all GPUs

Remove all GPU accelerator blanks

To remove the short GPU power cables for slots 3 and 4:

Remove the screws to release the retention springs.

Retain the screws for later use.

Disconnect the power cables from the power distribution board.

• 8 pin and 6 pin to 8 pin short GPU power cables

Replacing the GPU accelerator power cables

Содержание ProLiant XL270d Gen9































































































































Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы:

HP ProLiant XL270d Gen9, Руководство по техническому обслуживанию и ремонту, Страница: 54 / 126

Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы: