HP ProLiant XL270d Gen9 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 126

background image

Item

LED

Status

Definition

Flashing green

The drive is rebuilding or performing
a RAID migration, strip size
migration, capacity expansion, or
logical drive extension, or is erasing.

Flashing amber/green

The drive is a member of one or
more logical drives and predicts the
drive will fail.

Flashing amber

The drive is not configured and
predicts the drive will fail.

Solid amber

The drive has failed.

Off

The drive is not configured by a
RAID controller.

IMPORTANT:

The Dynamic Smart Array B140i Controller is only available in UEFI Boot Mode. It cannot be
enabled in Legacy BIOS Boot Mode. If the B140i controller is disabled, drives connected to the
system board Mini-SAS connectors operate in AHCI or Legacy mode. Under this condition:

• The drives cannot be a part of a hardware RAID or a logical drive.

• The Locate, Drive status, and Do not remove LEDs of the affected drives are disabled.

Use BIOS/Platform Configuration (RBSU) in the

UEFI System Utilities

to enable or disable the

B140i controller (System Configuration

®

BIOS/Platform Configuration (RBSU)

®

System Options

®

SATA Controller Options

®

Embedded SATA Configuration).

GPU accelerator numbering

• Server left GPU accelerator numbering

106

GPU accelerator numbering

«
...
104
105
106
107
108
...
»

Содержание ProLiant XL270d Gen9































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProLiant XL270d Gen9

Express5800/180Ra-7

Бренд: NEC Страницы: 2

Express5800/120Rh-2

Бренд: NEC Страницы: 2

Express5800/120Rh-2

Бренд: NEC Страницы: 2

Express5800/120Rg-1

Бренд: NEC Страницы: 2

Express5800/120Rf-1

Бренд: NEC Страницы: 21

Express5800/120Ra-1

Бренд: NEC Страницы: 6

Express5800/120Mc2 series

Бренд: NEC Страницы: 2

EXPRESS5800/120Le

Бренд: NEC Страницы: 56

Express5800 320La

Бренд: NEC Страницы: 8

Express5800 120Li

Бренд: NEC Страницы: 2

Express5800 120Ed

Бренд: NEC Страницы: 29

Active Upgrade Express5800/320Fc

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 10

Express5800/120Rj-2

Бренд: NEC Страницы: 18

Express5800/120Rh-1

Бренд: NEC Страницы: 20

Bull NovaScale R620 Series

Бренд: NEC Страницы: 346

Express5800 320La

Бренд: NEC Страницы: 206

Express5800/R110j-1

Бренд: NEC Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды