HP ProLiant XL270d Gen9 Скачать руководство пользователя страница 105

Страница: 105 / 126

Hot-plug drive LED definitions

Item

LED

Status

Definition

Locate

Solid blue

The drive is being identified by a
host application.

Flashing blue

The drive carrier firmware is being
updated or requires an update.

Activity ring

Rotating green

Drive activity.

Off

No drive activity.

Do not remove

Solid white

Do not remove the drive. Removing
the drive causes one or more of the
logical drives to fail.

Off

Removing the drive does not cause
a logical drive to fail.

Drive status

Solid green

The drive is a member of one or
more logical drives.

Table Continued

Hot-plug drive LED definitions

105

Содержание ProLiant XL270d Gen9































































































































Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы:

Похожие инструкции для ProLiant XL270d Gen9

Бренды по названию

Популярные бренды

HP ProLiant XL270d Gen9, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы:

Похожие инструкции для ProLiant XL270d Gen9

Бренды по названию

Популярные бренды