HP ProLiant XL270d Gen9 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 126

background image

•

Remove the access panel

•

Remove the side panel

•

Remove the air baffle

•

Remove the drive cage assembly

.

•

Remove the riser cross bracket

•

Remove the power riser

.

•

Remove the GPU accelerator

.

•

Remove the GPU accelerator blank

•

Remove the HPE Smart Array P542D Storage Controller module

Powering down the server

Before powering down the server for any upgrade or maintenance procedures, perform a backup of
critical server data and programs.

CAUTION:

Before powering down the server, perform a backup of critical server data and programs. Removing
the server while the Do not remove LED is on may result in data loss or corruption. The server can
be safely removed from the chassis only after the

Do not remove LED is off

IMPORTANT:

When the server is in standby mode, auxiliary power is still being provided to the system.

To power down the server , use one of the following methods:

• Press and release the Power On/Standby button.

This method initiates a controlled shutdown of applications and the OS before the server enters
standby mode.

• Press and hold the Power On/Standby button for more than 4 seconds to force the server to enter

standby mode.

This method forces the server to enter standby mode without properly exiting applications and the OS.
If an application stops responding, you can use this method to force a shutdown.

• Use a virtual power button selection through iLO .

This method initiates a controlled remote shutdown of applications and the OS before the server
enters standby mode.

Before proceeding, verify that the server is in standby mode by observing that the system power LED is
amber.

Removing the server from the chassis

CAUTION:

Before powering down the server, perform a backup of critical server data and programs. Removing
the server while the Do not remove LED is on may result in data loss or corruption. The server can
be safely removed from the chassis only after the

Do not remove LED is off

30

Powering down the server

«
...
28
29
30
31
32
...
»

Содержание ProLiant XL270d Gen9































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProLiant XL270d Gen9

ColorPASS-Z5000

Бренд: Canon Страницы: 130

eServer 380 xSeries

Бренд: IBM Страницы: 112

Бренд: Buffalo Страницы: 2

Бренд: Supermicro Страницы: 113

Бренд: FS Страницы: 91

Бренд: Thecus Страницы: 94

Бренд: XtendLan Страницы: 38

Бренд: Gigabyte Страницы: 21

Бренд: Webster Страницы: 114

Бренд: Lantronix Страницы: 68

Бренд: Gateway Страницы: 34

Бренд: Oracle Страницы: 44

Бренд: Oracle Страницы: 78

Бренд: Inspur Страницы: 4

Бренд: XtendLan Страницы: 16

Бренд: IEI Technology Страницы: 90

Бренд: Igel Страницы: 4

iP100 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды