HP ProLiant XL270d Gen9 Скачать руководство пользователя страница 99

Страница: 99 / 126

Front panel LEDs and buttons

Item

Description

Status

Power button/LED

Solid green = System on

Flashing green = Performing power on sequence

Solid amber = System in standby

Off = No power present

UID button/LED

Solid blue = Activated

• 1 flash per second = Remote management or

firmware upgrade in progress

• 4 flashes per second = iLO manual soft reboot

sequence initiated

• 8 flashes per second = iLO manual hard reboot

sequence in progress

Off = Deactivated

Health LED

Solid green = Normal

Flashing amber = System degraded

Flashing red = System critical

Do not remove LED

Flashing white = Do not remove the node. Removing
the node may terminate the current operation and
cause data loss.

Off = The node can be removed.

Table Continued

Front panel LEDs and buttons

Содержание ProLiant XL270d Gen9































































































































Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы:

HP ProLiant XL270d Gen9, Руководство по техническому обслуживанию и ремонту, Страница: 99 / 126

Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы: