HP Netserver LP 2000r Скачать руководство пользователя страница 83

Страница: 83 / 98

Chapter 6

Replacing Parts

9. Align the notches on the DIMM with the keys on the slot.

Retaining Latches (2)

DIMM Slot

Keys

Notches

DIMM to Slot Alignment

10. Hold the DIMM at approximately 30

to the system board and press the DIMM firmly and evenly

into the slot until the retaining latches close.

It is important to hold the DIMM firmly with both hands and use even pressure so as not to bend
or break the DIMM connector during installation. If the latches do not close, the DIMM is not
inserted correctly.

DIMM
Slots

System Board

DIMM Insertion

11. Repeat Steps 6-10 to install additional DIMMs for your memory configuration.

Removing an Accessory Board

Use this procedure to remove any accessory board.

NOTE

For information about a specific PCI board type, refer to the Readme file, Tested
Products List, or Configuration Advisor on your

HP Netserver Navigator CD-ROM

1. Log off all users and, if necessary, back up files.

2. Press the power switch on the HP Netserver control panel to turn off power when prompted by

the operating system.

Содержание Netserver LP 2000r



































































































Результаты поиска

Содержание Netserver LP 2000r

Отзывы:

HP Netserver LP 2000r, Руководство по обслуживанию, Страница: 83 / 98

Результаты поиска

Содержание Netserver LP 2000r

Отзывы: