manualshive.com logo in svg

HP Netserver LP 2000r, Руководство по обслуживанию, Страница: 45 / 98

Поделиться
Скачать
HP Netserver LP 2000r Скачать руководство пользователя страница 45

Chapter 4

Diagnostics

39

Code

Description

Problem/Solution

0801

Cache boot error

POST has detected an error in the cache memory module.

To correct this:

1. Verify the processor is installed correctly.

2. If the problem persists, the processor may need to be

replaced. Contact your service representative.

0900

Integrated LAN
disable error

The system could not disable the integrated LAN.

To correct this:

1. Reset the Integrated LAN by powering off the HP Netserver.

2. Disconnecting the power cord(s)for 20 seconds.

3. Reconnect the power cord(s) and power on the HP

Netserver.

4. If the error appears upon restarting, update the system BIOS.

5. Insert the HP Navigator CD-ROM in the CD-ROM drive and

power-cycle your system.

This will initialize the flash utility on HP Navigator CD-ROM.

6. If the error persists, the system board may need to be

replaced. Contact your service representative to replace your
Netserver.

0901

Integrated LAN
enable error

The system could not enable the integrated LAN.

To correct this:

1. Reset the Integrated LAN by powering off the HP Netserver.

2. Disconnecting the power cord(s) for 20 seconds.

3. Reconnect the power cord(s) and power on the HP

Netserver.

4. If the error appears upon restarting, update the system BIOS.

5. Insert the HP Navigator CD-ROM in the CD-ROM drive and

power-cycle your system.

This will initialize the flash utility on HP Navigator CD-ROM.

6. If the error persists, the system board may need to be

replaced. Contact your service representative to replace your
Netserver.

0A00

Display refresh rate
error

The parameters returned by the display do not match the DDC
standard used by the Netserver for automatic setup of ergonomic
refresh rates.

To correct this:

1. Disable the 'Plug & Play Display' feature in the 

Setup Utility

to avoid a blank or unreadable screen at power-up.

2. Use the 

Setup Utility

 to manually set the video refresh rates

to the highest ergonomic refresh rates supported by the
display. Refer to the display monitor's User Guide for
specifications.

Содержание Netserver LP 2000r



































































































Отзывы:

Нет отзывов