manualshive.com logo in svg

HP Netserver LP 2000r, Руководство по обслуживанию, Страница: 36 / 98

Поделиться
Скачать
HP Netserver LP 2000r Скачать руководство пользователя страница 36

Chapter 4

Diagnostics

30

Table 4-1. POST Error Messages

Message

Corrective Action

Operating
system not
found

•  

Verify the desired boot drive has power and its SCSI cable connected.

•  

Verify the SCSI cable is securely plugged into the SCSI connector on the

system board.

•  

Verify the boot device is enabled in the 

Setup Utility

 under the Security menu.

•  

Verify the boot device has an operating system installed.

If the problem persists, contact your HP support organization.

Keyboard error
(The LP 2000r
will complete
the boot
process without
a keyboard
connected.)

•  

Verify the keyboard is connected to the correct connector (not the mouse

connector) at the rear of the Netserver.

If the problem persists, replace the keyboard or contact your HP support
organization.

Mouse error
(The LP 2000r
will complete
the boot
process without
a mouse
connected.)

•  

Verify the mouse is connected to the correct connector (not the keyboard

connector) at the rear of the Netserver.

If the problem persists, replace the mouse or contact your HP support
organization.

If no message
appears
(screen is
blank)

•  

If no text or messages appear listen for the beep codes. Refer to Beep Codes

in Table 4-3.

•  

If no message appears but the Netserver stops after POST, verify the DIMMs

are correctly installed.

If a
configuration
error occurs

If a Netserver configuration error is reported during the startup routine, clear the
CMOS memory as described under "Clearing the CMOS Configuration," and restart
the Netserver.

System CMOS
checksum bad

•  

Press 

[F2] 

to run Setup.

•  

Change settings as required.

•  

Choose the Exit option, selecting Save Changes and Exit to save the new

settings.

The Netserver should reboot.

Power On Self Test (POST) Error Codes

The error codes (POST codes) appear in normal video if an error condition occurs during the boot process of
the HP Netserver LP 2000r. All the codes and the respective descriptions are listed in the 

HP Netserver LP

2000r Service Manual

, but not all the codes apply to this Netserver. The service manual is also located on

the 

HP Netserver Online Documentation CD-ROM 

provided with the HP Netserver.

The codes will appear on the display monitor, provided it and the supporting circuitry are functioning:

NOTE

Do not take remove/replacement actions until you have taken other troubleshooting
steps. See the troubleshooting checklist.

Содержание Netserver LP 2000r



































































































Отзывы:

Нет отзывов