HP Netserver LP 2000r Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 98

HP Netserver LP 2000r Скачать руководство пользователя страница 38

Chapter 4

Diagnostics

32

Code

Description

Problem/Solution

0021

PCI Configuration
conflict

A configuration problem has occurred with a PCI device. The PCI
device or accessory board doesn’t match PC setup settings or has
conflicts with PC resources (reserved memory space, IRQ or DMA
channels).

To correct this:

1. Clear the PCI configuration with the Configuration switch.

Refer to " Clearing the CMOS Configuration”.

2. If necessary, use the

Setup Utility

to manually configure the

PCI devices.

3. Check for any further PC resource, which can be used. Use

Setup Utility

to disable any unused function, such as I/O

ports or IDE controllers.

4. Start the Operating System and let it update the PCI

configuration.

0022

Plug & Play ISA
initialization problem
(This does not apply
to LP 2000r)

The Plug & Plug ISA accessory board has reported an initialization
problem. The ROM on the accessory board is bad or the Plug & Play
BIOS cannot solve a conflict issue with a system board reserved
resource.

To correct this:

1. Clear the Plug & Play configuration with the CMOS status

switch. Refer to the User's guide for details.

2. Try to disable (free) resources used by system board

devices.

3. Run the Plug & Play utility supported by your Operating

System.

4. If the problem persists, the accessory board may be

defective. Contact the accessory board vendor.

0030

Processor Speed
selection problem
(This does not apply
to LP 2000r.)

POST has detected the processor speed selected with system board
switches does not match the processor's speed.

0040

PC Serial Number
initialization problem
(This does not apply
to LP 2000r – The
system serial number
is entered in the
manufacturing
process and stored in
the system FRU
data.)

POST has detected the PC Serial Number has been lost or has not
been initialized.

Pressing

[F2]

will automatically run the HP Serial (BIOS) Utility

and allow you to enter the Serial Number.

0050

Processor Cooling/
Heating problem

POST has detected a cooling fan problem.

The processor cooling-fan needs to be connected or it is not
turning fast enough to cool the processor. The system board
circuitry monitors the speed of all the fans.

«
...
36
37
38
39
40
...
»

Содержание Netserver LP 2000r



































































































Отзывы:

Нет отзывов