manualshive.com logo in svg

HP Netserver LP 2000r, Руководство по обслуживанию, Страница: 5 / 98

Поделиться
Скачать
HP Netserver LP 2000r Скачать руководство пользователя страница 5

Contents

v

Preventive Maintenance Procedures ........................................................................................................... 47

Troubleshooting Tips.................................................................................................................................... 47

Troubleshooting Checklist ....................................................................................................................... 48

BIOS Recovery............................................................................................................................................. 49

Password Problems ..................................................................................................................................... 51

Resetting Lost Passwords ....................................................................................................................... 51

General Netserver Problems ....................................................................................................................... 52

Power Problems........................................................................................................................................... 53

Video/Monitor Problems............................................................................................................................... 54

Configuration Problems................................................................................................................................ 56

Printer/Datacomm Problems........................................................................................................................ 57

Keyboard and Mouse Problems................................................................................................................... 58

Flexible Disk Drive Problems ....................................................................................................................... 59

CD-ROM Problems ...................................................................................................................................... 60

SCSI Problems............................................................................................................................................. 61

Processor Problems..................................................................................................................................... 64

Memory Problems ........................................................................................................................................ 65

Network Interface Card Problems................................................................................................................ 65

6 Replacing Parts .......................................................................................................................................... 67

Safety Information ........................................................................................................................................ 67

Tools and Supplies Needed ......................................................................................................................... 67

Safety: Before You Remove Server Covers ................................................................................................ 67

Warnings and Cautions................................................................................................................................ 68

Removing the Front Bezel............................................................................................................................ 69

Replacing the Front Bezel............................................................................................................................ 69

Removing the Top Cover ............................................................................................................................. 69

Replacing the Top Cover ............................................................................................................................. 70

Removing the Air Flow Guide ...................................................................................................................... 71

Replacing the Air Flow Guide....................................................................................................................... 71

Removing Hot Swap Hard Drives ................................................................................................................ 71

Installing Hot Swap Hard Drives .................................................................................................................. 73

Removing DIMMs......................................................................................................................................... 75

Installing Additional DIMMs.......................................................................................................................... 75

Содержание Netserver LP 2000r



































































































Отзывы:

Нет отзывов