6Ć12
Removal and Replacement
C4699Ć90000
Reinstalling the frontĆpanel assembly:
Insert the bottom of the assembly into the two
indicated notches, inside the right endĆcover.
Then
firmly
reinsert the top two tabs.
Notch
Push the front panel from the outside, to check
whether it is correctly installed.
Reinstalling the right endĆcover:
Before
replacing the endĆcover, make sure that
a
The black plastic piece at the front end of
the pinchĆarm linkage is correctly
attached to the sideĆplate.
b
The lever nut is positioned inside the slot
on the black plastic piece.
Nut
Black plastic piece
Disconnecting the FrontĆPanel
Assembly
Remove the right endĆcover
page 6Ć10.
Onthe mainPCA, gently pull the
frontĆpanel connector clamp (FP) to the
right to release the flat, white cable.
Pull the cable easily out of the clamp, and
release it from the clip onthe side of the
electronics module.
FP
COVER
Reassembling:
The contact part of the
cable faces down. Prevent tugging of the
cable at the point of connection by leaving
slack between the connector and the clip.
Detach the topĆcoverĆsensor cable from
the COVER connector, and release it from
the clip onthe side of the electronics
module.
Содержание Designjet 230
