background image

Technical Reference Guide

www.hp.com

4-13

System Support

4.5.3 System Status

These systems provide a visual indication of system boot, ROM flash, and operational status 
through the power LED and internal speaker, as described in Table 4-8.

.

NOTES:

Beeps are repeated for 5 cycles, after which only blinking LED indication continues.
[1] Repeated after 2 second pause.
[2] Beeps are produced by the internal chassis speaker.
[3] Check that CPU power connector P3 is plugged in.

Table 4-8.

System Operational Status LED Indications

System Status

PowerLED

 Beeps [2]

Action Required

S0: System on (normal 

operation)

Steady green

None

None

S1: Suspend

Blinks green @ .5 Hz

None

None

S3: Suspend to RAM

Blinks green @ .5 Hz

None

None

S4: Suspend to disk

Off – clear

None

None

S5: Soft off

Off – clear

None

None

Processor thermal shutdown

Blinks red 2 times @ 1 Hz [1]

2

Check air flow, fans, heatsink

Processor not seated / installed Blinks red 3 times @ 1 Hz [1]

3

Check processor 

presence/seating

Power supply overload failure

Blinks red 4 times @ 1 Hz [1]

4

Check system board problem 

[3], 

Memory error (pre-video)

Blinks red 5 times @ 1 Hz [1]

5

Check DIMMs, system board

Video error

Blinks red 6 times @ 1 Hz [1]

6

Check graphics card or 

system board

PCA failure detected by BIOS 

(pre-video)

Blinks red 7 times @ 1 Hz [1]

7

Replace system board

Invalid ROM checksum error

Blinks red 8 times @ 1 Hz [1]

8

Reflash BIOS ROM

Boot failure (after power on)

Blinks red 9 times @ 1 Hz [1]

9

Check power supply, 

processor, sys. bd

Bad option card

Blinks red 10 times @ 1 Hz [1]

None

Replace option card

Содержание 8100 - Elite Convertible Minitower PC

















































































































Отзывы: