HP 8100 - Elite Convertible Minitower PC Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 112

background image

Technical Reference Guide

www.hp.com

6-5

Integrated Graphics Subsystem

6.3 Upgrading

These systems provide direct, dual-monitor support; a VGA montor and a DisplayPort monitor
can be connected and driven simultaneously. These systems also include a PCIe x16 graphics
connector that specifically supports a PCIe x16 graphics card and a PCIe x16 connector that
provides PCIe x4 operation for an x4 or x16 PCIe card.

The upgrade procedure is as follows:

1. Shut down the system through the operating system.

2. Unplug the power cord from the rear of the system unit.

3. Remove the chassis cover.

4. Install the graphics card into the PCIe x16 graphics slot or the PCIe x4/x16 slot.

5. Replace the chassis cover.

6. Reconnect the power cord to the system unit.

7. Power up the system unit:

✎

If a PCIe graphics controller card is installed in the PCIe x16 graphics slot, the BIOS will detect
the presence of the PCIe card and disable the integrated graphics controller of the processor. In
this configuration, the integrated graphics controller cannot be enabled.

If a PCIe graphics controller card is installed in the PCIe x4 /x16 slot, the integrated graphics
controller of the processor will be disabled by default, but can be re-enabled through the BIOS
settings to allow an alternate method of multi-monitor operation. Press the

F10

key during the

boot process to enter the ROM-based Setup utility and re-enable the GMA for multi-monitor
operation. A PCIe x16 card installed in the PCIe x4/x16 slot will be limited to x4 operation.

✎

Two PCIe graphics can be installed simultaneously to provide an alternate method for
multi-monitor support. In this configuration, the integrated graphics controller (if present) will be
disabled.

«
...
69
70
71
72
73
...
»

Содержание 8100 - Elite Convertible Minitower PC

















































































































Отзывы:

Нет отзывов

Похожие инструкции для 8100 - Elite Convertible Minitower PC

Бренд: ACE COMPUTERS Страницы: 37

Бренд: IBM Страницы: 52

Бренд: Zotac Страницы: 28

Essentio CG5275

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 8

Бренд: Aaeon Страницы: 101

Бренд: Toshiba Страницы: 2

PX30 - A Series

Бренд: Toshiba Страницы: 147

Бренд: Toshiba Страницы: 149

Бренд: Toshiba Страницы: 143

Бренд: Toshiba Страницы: 162

Бренд: Toshiba Страницы: 174

mini NB250 series

Бренд: Toshiba Страницы: 222

Бренд: Toshiba Страницы: 236

Бренд: Toshiba Страницы: 270

Бренд: Toshiba Страницы: 279

Бренд: Toshiba Страницы: 159

Portege R400 Series

Бренд: Toshiba Страницы: 369

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды