HP 8100 - Elite Convertible Minitower PC Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 112

background image

4-14

www.hp.com

Technical Reference Guide

System Support

4.5.4 Thermal Sensing and Cooling

All systems feature a variable-speed fan mounted as part of the processor heatsink assembly. All
systems also provide or support an auxiliary chassis fan. All fans are controlled through
temperature sensing logic on the system board and/or in the power supply. There are some
electrical differences between form factors and between some models, although the overall
functionally is the same. Typical cooling conditions include the following:

1. Normal—Low fan speed.

2. Hot processor—ASIC directs Speed Control logic to increase speed of fan(s).

3. Hot power supply—Power supply increases speed of fan(s).

4. Sleep state—Fan(s) turned off. Hot processor or power supply will result in starting fan(s).

The RPM (speed) of all fans is the result of the temperature of the CPU as sensed by speed
control circuitry. The fans are controlled to run at the slowest (quietest) speed that will maintain
proper cooling.

✎

Units using chassis and CPU fans must have both fans connected to their corresponding headers
to ensure proper cooling of the system.

4.6 Register Map and Miscellaneous Functions

This section contains the system I/O map and information on general-purpose functions of the
PCH and I/O controller.

4.6.1 System I/O Map

Table 4-9 lists the fixed addresses of the input/output (I/O) ports.

«
...
46
47
48
49
50
...
»

Содержание 8100 - Elite Convertible Minitower PC

















































































































Отзывы:

Нет отзывов

Похожие инструкции для 8100 - Elite Convertible Minitower PC

Бренд: NEC Страницы: 127

Бренд: Asus Страницы: 18

Бренд: Asus Страницы: 174

Бренд: Asus Страницы: 166

Бренд: Partners Страницы: 3

Бренд: Dell Страницы: 72

Cabling Sitting/Standing Workstation

Бренд: VS Страницы: 8

Satellite M100 Series

Бренд: Toshiba Страницы: 2

Satellite M100 Series

Бренд: Toshiba Страницы: 283

Flex Insight XMS

Бренд: Spectrum Industries Страницы: 11

Бренд: PROAIM Страницы: 4

Бренд: Onyx Страницы: 2

Бренд: Moxa Technologies Страницы: 57

Бренд: 3Com Страницы: 122

Бренд: W&T Страницы: 30

Бренд: Nexcom Страницы: 71

Бренд: Nexcom Страницы: 96

Бренд: Nexcom Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды