HP 3020 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 34

background image

33

Release Notes for the Cisco Catalyst Blade Switch 3020 for HP, Cisco IOS Release 12.2(55)SE and Later

OL-22861-04

Documentation Updates

Error Message

DOT1X-5-SUCCESS: Authentication successful for client ([chars]) on

Interface [chars]

Explanation

Authentication was successful. [chars] is the interface.

Recommended Action

No action is required.

Error Message

DOT1X_SWITCH-5-ERR_ADDING_ADDRESS: Unable to add address [enet] on

[chars]

Explanation

The client MAC address could not be added to the MAC address table because the

hardware memory is full or the address is a secure address on another port. This message might
appear if IEEE 802.1x is enabled. [enet] is the client MAC address, and [chars] is the interface.

Recommended Action

If the hardware memory is full, remove some of the dynamic MAC addresses.

If the client address is on another port, remove it from that port.

Error Message

SW_VLAN-4-VTP_USER_NOTIFICATION: VTP protocol user notification:

[chars].

Explanation

This message means that the VTP code encountered an unusual diagnostic situation.

[chars] is a description of the situation.

Recommended Action

Find out more about the error by using the s

how tech-support

privileged

EXEC command. Copy the message exactly as it appears on the console or in the system log.
Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to
look for similar reported problems. If you still require assistance, open a case with the TAC, or
contact your Cisco technical support representative, and provide the representative with the gathered
information.

Updates to the Getting Started Guide

This illustration in the

Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide

has been updated:

Figure 1

The Catalyst Blade Switch 3020 for HP

1

Switch module

7

Health LED

2

Release latch

8

SFP module port LEDs for ports 17 to 20

3

System status LEDs

9

SFP module ports 17 to 20

153139

23x

24x

21x

24x

17x

18x

17x

20x

17

20

SYST
STAT

DLX

SPD

CONSOLE

UID

WS-CBS-3020-HPQ

MODE

MEDIA D

ETECT SFP

/R-45 PO

RTS 17-20

17

20

18

19

2

3

8

10

4

9

1

6

7

11

5

«
...
31
32
33
34
»

Содержание 3020



































Отзывы:

Нет отзывов

Похожие инструкции для 3020

Бренд: Kaleidescape Страницы: 11

ApplianceStor 15MT

Бренд: Rasilient Страницы: 30

AMX Vision2 V2-MASTER-1210

Бренд: Harman Страницы: 2

Бренд: TAPKO Страницы: 2

NPort W2150Plus Series

Бренд: Moxa Technologies Страницы: 167

Бренд: IOGear Страницы: 44

Бренд: NEC Страницы: 138

Бренд: Hitachi Страницы: 57

Бренд: Hitachi Страницы: 76

BladeSymphony 1000

Бренд: Hitachi Страницы: 52

Бренд: Hitachi Страницы: 91

Бренд: Hitachi Страницы: 174

HVM Navigator V03-06

Бренд: Hitachi Страницы: 312

NVM Navigator v03-07

Бренд: Hitachi Страницы: 316

Бренд: Hitachi Страницы: 129

Бренд: Hitachi Страницы: 466

Бренд: Hitachi Страницы: 530

Бренд: Acer Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды