HP 3020 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 34

HP 3020 Скачать руководство пользователя страница 14

14

Release Notes for the Cisco Catalyst Blade Switch 3020 for HP, Cisco IOS Release 12.2(55)SE and Later

OL-22861-04

Resolved Caveats

•

CSCth94904

An internal switch port is down when one of these HP Flex 10-Gigabit Ethernet network interface
cards (NICs) is up:

–

Flex 522m Mezz

–

Flex 542m Mezz

–

Flex 552m Mezz

The workaround is to use the

speed nonegotiate

interface configuration command on the internal

port.

•

CSCto57605

If the Dynamic Trunking Protocol (DTP) is set to speed nonegotiate for two switches that interface
each other, and the speed/duplex is configured as full/1000, the speed/duplex configuration of one
of the switches changes to auto/auto when the switch is restarted. The port channel becomes
incompatible and the second switch’s operation is suspended. This problem applies only to the
1000BASE-LX interface.

The workaround is to enter the

shutdown

interface configuration command followed by the

no

shutdown

command.

•

CSCtx73953

A port that is programatically configured with auth-default ACL does not allow any traffic on the
switch except DHCP traffic. If the configurations on the interface are cleared and the interface is
restarted, the auth-default ACL configuration remains and the problem persists.

There is no workaround.

Resolved Caveats

•

Caveats Resolved in Cisco IOS Release 12.2(55)SE5, page 14

•

Caveats Resolved in Cisco IOS Release 12.2(55)SE4, page 17

•

Caveats Resolved in Cisco IOS Release 12.2(55)SE3, page 19

•

Caveats Resolved in Cisco IOS Release 12.2(55)SE2 and Earlier, page 20

Caveats Resolved in Cisco IOS Release 12.2(55)SE5

•

CSCsy43147

During a Telnet session, the router crashes when the server is configured or unconfigured
(

tacacs-server host

command) using the

single-connection

keyword.

The workaround is to not use the

single-connection

keyword.

•

CSCtb35715

When you enter the

show running-config

interface configuration command, IP Service Level

Agreement notifications are shown as enabled even when you have not enabled this configuration
using the

ip sla enable reaction-alerts

interface configuration command.

There is no workaround.

«
...
12
13
14
15
16
...
»

Содержание 3020



































Отзывы:

Нет отзывов