HP 3020 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 34

HP 3020 Скачать руководство пользователя страница 23

23

Release Notes for the Cisco Catalyst Blade Switch 3020 for HP, Cisco IOS Release 12.2(55)SE and Later

OL-22861-04

Resolved Caveats

•

CSCtf78276

A switch running Cisco IOS Release 12.2(53)SE1 stops when IEEE 802.1x authentication is
enabled.

The workaround is to apply a VLAN that the RADIUS server assigned to the switch.

•

CSCtg26941

Multidomain authentication (MDA) with guest VLAN or MAC authentication bypass (MAB) as a
fallback method is enabled on a switch running Cisco IOS Release 12.2(53)SE. When a non-802.1x
client is connected to a IP phone and the phone connected to a switch port shuts down and then
restarts, the client MAC address status is

drop

in the MAC address table. It takes 5 minutes for the

client to access the network.

The workaround is to use another software release, such as Cisco IOS Release 12.2(44)SE2.

•

CSCtg47738

This error message is displayed after copying a configuration file to the running configuration file
fails:

%Error opening system:/running-config (No such file or directory)

The output of the

dir system:/

EXEC command also does not show a running configuration file.

The workaround is to reload the switch.

•

CSCti04980

After you upgrade the switch software to Cisco IOS Release 12.2(55)SE, enhanced auto-QoS
commands are generated when

–

auto-QoS is enabled on an interface

and

–

mls qos

command is not enabled on the switch

If the

mls qos

command was already enabled on the switch, enhanced auto-QoS commands are

generated only when you configure one of these commands:

–

auto qos classify

[

police

]

–

auto qos trust

{

cos

|

dscp

}

–

auto qos video

{

cts

|

ip-camera

}

Cisco IOS Release 12.2(55)SE supports implicit and explicit migration to enhanced auto-QoS
configurations.

Implicit migration to enhanced auto-QoS occurs on a switch running legacy auto-QoS when you
configure the

auto qos video

,

auto qos trust

, or

auto qos classify

command

on an interface. Global

and interface configurations on the switch migrate to the enhanced video or trust auto-QoS
configurations.

Explicit migration to enhanced auto-QoS occurs on a switch when you enable the

auto qos srnd4

global configuration command. You can configure the [

no

] form of this commandafter you remove

auto-QoS functionality from all switch interfaces.

•

CSCtj03875

When you disconnect the spanning tree protocol (STP) peer link, the STP port path cost
configuration changes.

There is no workaround.

«
...
21
22
23
24
25
...
»

Содержание 3020



































Отзывы:

Нет отзывов