manualshive.com logo in svg

HP 3020, Руководство по выпуску, Страница: 30 / 34

Поделиться
Скачать
HP 3020 Скачать руководство пользователя страница 30

 

30

Release Notes for the Cisco Catalyst Blade Switch 3020 for HP, Cisco IOS Release 12.2(55)SE and Later

OL-22861-04

Documentation Updates

Error Message

DOT1X_SWITCH-5-ERR_PRIMARY_VLAN_NOT_FOUND: Attempt to assign VLAN 

[dec], whose primary VLAN does not exist or is shutdown, to 802.1x port [chars] 

AuditSessionID [chars] 

Explanation

An attempt was made to assign a private VLAN whose primary VLAN does not exist or 

is shut down. [dec] is the VLAN, the first [chars] is the port, and the second [chars] is the session ID. 

Recommended Action

Make sure that the primary VLAN exists and is not shut down. Verify that the 

private VLAN is associated with a primary VLAN. 

Note

This message applies to switches running the IP base image. 

Error Message

DOT1X_SWITCH-5-ERR_SEC_VLAN_INVALID: Attempt to assign secondary VLAN 

[dec] to non-PVLAN host 802.1x port [chars] AuditSessionID [chars] 

Explanation

An attempt was made to assign a secondary VLAN to a port that is not a private VLAN 

host port, which is not allowed. [dec] is the VLAN, the first [chars] is the port, and the second [chars] 
is the session ID. 

Recommended Action

Change the port mode so that it is configured as a private VLAN host port, or 

use a different VLAN that is not configured as a secondary VLAN. 

Error Message

DOT1X_SWITCH-5-ERR_SPAN_DST_PORT: Attempt to assign VLAN [dec] to 

802.1x port [chars], which is configured as a SPAN destination AuditSessionID 

[chars] 

Explanation

An attempt was made to assign a VLAN to an 802.1x port that is configured as a 

Switched Port Analyzer (SPAN) destination port. [dec] is the VLAN, the first [chars] is the port, and 
the second [chars] is the session ID. 

Recommended Action

Change the SPAN configuration so that the port is no longer a SPAN destination 

port, or change the configuration so that no VLAN is assigned. 

Error Message

DOT1X_SWITCH-5-ERR_VLAN_EQ_MDA_INACTIVE: Multi-Domain Authentication 

cannot activate because Data and Voice VLANs are the same on port AuditSessionID 

[chars] 

Explanation

Multi-Domain Authentication (MDA) host mode cannot start when the configured data 

VLAN on a port is the same as the voice VLAN. [chars] is the port session ID. 

Recommended Action

Change either the voice VLAN or the access VLAN on the interface so that they 

are not the same. MDA then starts.

Содержание 3020



































Отзывы:

Нет отзывов