Hoval UltraOil 50 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 44

Hoval UltraOil 50 Скачать руководство пользователя страница 6

4 210 256 / 01

6

Assembly

2.2.1 Design variants

i

Before commissioning, the neutrali-
sation box (if fitted) must be filled with
neutralisation granulate (figure, chap-
ter 6.4).

Before putting into service, the si-
phon and the neutralisation box must
be filled with water.
The water can be filled through the
cleaning opening into the neutralisa-
tion box and the siphon.

Possibility 1

• Stand version with siphon
• With neutralisation, condensate discharge into

lower drain line.

• Drain optionally on the left or right side

.

1

3

2

Possibility 2

• Design with neutralisation box
• For condensate discharge in lower drain line, incl.

condensate neutralisation.

1

3

2

Possibility 3

• Siphon and condensate delivery pump
• Without neutralisation, condensate discharge into

higher drain line.

i

The condensate delivery pump must
be installed in accordance with the
enclosed instructions.

1

2

Possibility 4

• Neutralisation box and condensate delivery pump
• With condensate neutralisation - condensate dis-

charge into higher drain line.

i

The condensate delivery pump must
be installed in accordance with the
enclosed instructions.

3

2

1

4

«
...
4
5
6
7
8
...
»

Содержание UltraOil 50













































Отзывы:

Нет отзывов