Hoval UltraOil 50 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 44

Hoval UltraOil 50 Скачать руководство пользователя страница 18

4 210 256 / 01

18

Installation

Control power plug

for connecting the electrical
components e.g. sensors etc.

Strain-relief

all cables must be fit-
ted with strain-reliever
clamps.

Power supply 230V

Terminal strip

for external components
e.g. condensate pump-
ing station etc.

4.4.1 Safety measures relating to EMC as-

sembly

1. For regulator units with their own power supply,

separate laying of power leads and sensor or
bus-leads is absolutely essential. If using cable
channelling, only that fitted with separator strips
may be used.

2. The power connection to the heating equipment

(boiler-switchboard-regulator unit) must be desig-
ned as an independent electrical circuit. Neither
fluorescent lamps nor any other machinery which
might cause interference may be connected, nor
may it be possible to make such a connection.

Cut-out
Boiler room emergency
switch

Heater

Boiler room lighting and
sockets to be connected to
a separate circuit

3. The external sensor must not be installed in the

vicinity of transmitter or receiver fittings, for ex-
ample on a garage wall near receivers for remote
garage door openers, ham-radio aerials or radio
alarm systems, or in the immediate vicinity of
trans mitters etc.

Recommended cable cross-sections and max i-
mum permitted lengths of cable:

Cables carrying mains supply voltages: (power
con

nections, burners, pumps, setting motors

etc.): minimum 1mm

2

maximum permitted length: no restrictions, within
the framework of the building’s internal installati-
ons.
Sensor cables and cables carrying low voltages:
minimal 0.5 mm

2

maximum permitted cable length: 50 m
Data bus cables: must be screened e.g. J-Y (ST)
2 x 0.6 mm
maximum permitted cable length: 100 m

Fig. 11

«
...
16
17
18
19
20
...
»

Содержание UltraOil 50













































Отзывы:

Нет отзывов