2
3
GB
M
a
in
t
en
a
nce
a
nd
c
a
re
S
w
i
t
chin
g
t
he
a
ppli
a
nce
o
ff
Disconnect your appliance from the electricity supply
before carrying out any wor
k
on it.
Cl
e
a
n
i
n
g
t
h
e
a
pp
lia
n
c
e
The stainless-steel or enamel-coated external parts
as well as the rubber seals may be cleaned using a
sponge that has been soa
k
ed in lu
k
ewarm water
and neutral soap. If these stains are difficult to
remove, use only specialised products. After
cleaning, rinse and dry thoroughly. Do not use
abrasive powders or corrosive substances.
Ideally, the inside of the oven should be cleaned
after each use, when it is still lu
k
ewarm. Use hot
water and detergent, rinse and dry with a soft cloth.
Do not use abrasive products.
All accessories - with the exception of the sliding
rac
k
s - can be washed li
k
e everyday croc
k
ery, and
are even dishwasher safe.
Never use steam cleaners or pressure cleaners on
the appliance.
Cl
e
a
n
i
n
g
t
h
e
o
v
en
d
oor
Clean the glass part of the oven door using a sponge
and a non-abrasive cleaning product, then dry
thoroughly with a soft cloth. Do not use rough abrasive
material or sharp metal scrapers as these could
scratch the surface and cause the glass to crac
k
.
To clean more thoroughly, you can remove the oven
door.
1. Open the oven door fully (
see diagram
).
2. Lift up and turn the small levers located on the two
hinges (
see diagram
).
3. Grip the door on the two
external sides and close it
approximately half way. Unloc
k
the door by pressing on the
clamps
F
, then pull the door
towards you lifting it out of its
seat (
see diagram
).
To replace the door, reverse
this sequence.
I
nspec
t
ing
t
he
se
a
ls
Chec
k
the door seals around the oven periodically. If
the seals are damaged, please contact your nearest
After-sales Service Centre (
see Assistance
).
W
e
recommend not using the oven until the seals have
been replaced.
Re
p
la
c
i
n
g
t
h
e
li
gh
t
b
u
l
b
To replace the oven light bulb:
1. Remove the glass cover of the lamp-holder.
2. Remove the
light bulb and
replace it with a
similar one:
W
attage 25
W
,
cap E 14.
3. Replace the
glass cover (
see
diagram
).
S
li
d
i
n
g
R
a
ck
K
it
ass
e
m
b
l
y
To assemble the sliding rac
k
s:
1. Loosen the two
screws A (
see diagram
).
If the oven is fitted with
self-cleaning panels,
these will have to be
temporarily
disassembled.
2. Replace the screws A with the screws and spacers
(B
+
C) supplied with the
k
it.
3. Tighten the new screws B and the corresponding
spacers C, fitting the self-cleaning panels on again.
4. Secure the two joints
D of the guide rail in the
holes provided on the
oven walls (
see
diagram
). The holes for
the left guide rail are
situated at the top, while
the holes for the right
one are at the bottom.
5. Finally, fit the guide rail on the spacer C.
Do not place the sliding rac
k
s in position 5.
F
F
B
C
A
A
D
