Hoshizaki Serenity Series KMS-822MLH Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 47

Hoshizaki Serenity Series KMS-822MLH Скачать руководство пользователя страница 5

5

Important Safety Information

Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, or damage to the unit.

WARNING

Indicates a hazardous situation which could result in death or
serious injury.

CAUTION

Indicates a situation which could result in damage to the unit.

IMPORTANT

Indicates important information about the use and care of the
unit.

WARNING

This icemaker should be destined only to the use for which it has been
expressly conceived. Any other use should be considered improper and
therefore dangerous. The manufacturer cannot be held responsible for injury or
damage resulting from improper, incorrect, and unreasonable use.

To reduce the risk of death, electric shock, serious injury, or fire, follow
basic precautions including the following:

• This unit should be disassembled or repaired only by qualified service

personnel to reduce the risk of electric shock, injury, or fire.

• Move the control switch to the "OFF" position and turn off the power supply

to the SRK condensing unit before any servicing to the KMS or SRK is
undertaken. Place the KMS disconnect (if applicable) in the off position.
Lockout/Tagout to prevent the power supply from being turned back on
inadvertently.

• Do not make any alterations to the unit. Alterations could result in electric

shock, injury, fire, or damage to the unit.

For KMS

• Power supply and ground connection are supplied from the SRK remote

condensing unit via the wire harness provided. Do not connect the wire
harness leads to an external power source.

• Wire harness routing (conduit) and disconnect (if required) must meet

national, state, and local electrical code requirements. Failure to meet these
code requirements could result in death, electric shock, serious injury, fire, or
severe damage to equipment.

•

THE ICEMAKER MUST BE GROUNDED.

Failure to properly ground

the icemaker could result in death, serious injury, or severe damage to
equipment.

«
...
3
4
5
6
7
...
»

Содержание Serenity Series KMS-822MLH
















































Отзывы:

Нет отзывов