Hoshizaki Serenity Series KMS-822MLH Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 47

Hoshizaki Serenity Series KMS-822MLH Скачать руководство пользователя страница 17

17

3. Controls and Adjustments

CAUTION

Dip switches are factory set. Failure to maintain factory settings may adversely
affect performance and warranty coverage. For more information, contact
Hoshizaki Technical Support at 1-800-233-1940.

a) Default Dip Switch Settings

The dip switches are factory set to the following positions:

S4 Dip Switch

S4 Dip Switch No.

1

2

3

4

5

6

7

8

9

10

KMS-822MLH

OFF OFF OFF ON ON ON ON OFF OFF ON

S5 Dip Switch (Do Not Adjust)

S5 Dip Switch No. 1

2

3

4

5

KMS-822MLH

OFF OFF OFF OFF OFF

Freeze Timer (9 & 10)

Pump-Out Frequency Control (5 & 6)

Pump-Out Timer (3 & 4)
(Do not adjust out of factory setting)

Harvest Timer (1 & 2)

Harvest Pump Timer (7)
(Do not adjust)

Factory Use (8)

b) Harvest Timer (S4 dip switch 1 & 2)

The harvest timer starts when the thermistor reads 48°F (9°C) at the evaporator outlet
and the control board reads the thermistor's 3.9 kΩ signal. The harvest timer is factory
set, and generally no adjustment is required. However, a setting longer than the factory
setting may be advised in cases where harvest needs to be prolonged for extra cleaning.
Before changing this setting, contact your local Hoshizaki distributor or Hoshizaki
Technical Support for recommendations. Keep in mind that setting the harvest timer to a
longer setting decreases 24-hour production.
The pump-out timer (S4 dip switch 3 & 4) acts in place of the harvest timer during cycles
with a pump-out. For details, see "II.C.3.c) Pump-Out Timer (S4 dip switch 3 & 4)."

S4 Dip Switch Setting

Time

(seconds)

No. 1

No. 2

OFF

OFF

60

ON

OFF

90

OFF

ON

120

ON

ON

180

«
...
15
16
17
18
19
...
»

Содержание Serenity Series KMS-822MLH
















































Отзывы:

Нет отзывов