Hoshizaki Serenity Series KMS-822MLH Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 47

Hoshizaki Serenity Series KMS-822MLH Скачать руководство пользователя страница 30

30

2. Bin Control Cleaning

Scale may build up on BC. Scale can cause the actuator paddle and magnet to stick. In
this case, BC should be cleaned.

WARNING

CHOKING HAZARD:

Ensure all components, fasteners, and thumbscrews are

securely in place after the unit is serviced. Make sure that none have fallen into
the storage bin.

1) Turn off the power supply and clear any ice away from BC.
2) Remove the front panel, top panel, and right side panel, then move the control switch to

the "OFF" position.

3) Remove the control box cover.
4) Disconnect the red BC connector from CB RED K4 connector.
5) Follow the instructions below to remove BC.

a. Loosen the screws securing the control box, then lift the control box off and hang it

from the base. See Fig. 1.

b. Remove the insulation. Remove the thumbscrews securing the bin control assembly.

Remove the bin control assembly.

6) Remove BC from the extension bracket. See Fig. 3.
7) Wipe down BC assembly with a mixture of

1 part Hoshizaki "Scale Away" and 25 parts
warm water. Rinse the parts thoroughly
with clean water.

8) Reassemble BC assembly and replace it in

its correct position.

Note: If the magnet was removed for

cleaning, be sure to replace it in its
correct position.

9) Replace the control box in its correct

position and secure, then reconnect the red
BC connector to CB RED K4 connector.

10) Replace the control box cover.
11) Move the control switch to the "ICE" position.
12) Replace the panels in their correct positions.
13) Turn on the power supply to start the

automatic icemaking process.

Legend:

BC

–bin control

Fig. 3

Bin Control

Cover

Bin Control

Extension

Bracket

Actuator Paddle

Insulation

Magnet

Bin Control

Cable

Bin Control

«
...
28
29
30
31
32
...
»

Содержание Serenity Series KMS-822MLH
















































Отзывы:

Нет отзывов