manualshive.com logo in svg

Hoshizaki Serenity Series KMS-822MLH, Руководство по обслуживанию, Страница: 26 / 47

Поделиться
Скачать
Hoshizaki Serenity Series KMS-822MLH Скачать руководство пользователя страница 26

26

6) 

Pump-Out Cycle

 

– (10 second pump-out) – LEDs 1, 4, 3, and 2 are on.

 LED 4 (WV 

circuit) is on when S4 dip switch 3 & 4 are set to factory default positions of 3 off and 
4 on. With S4 dip switch 3 off & 4 on, CB energizes WV during pump-out. The WV 
circuit energizes DV through DVR during pump-out cycles. 

CAUTION! Do not adjust. 

S4 dip switch 3 & 4 must remain in the factory default position of 3 off and 
4 on. Otherwise, DV will not energize during pump-out.

 Comp and FMRs remain 

energized, WV and HGVs energize, LLVs de-energize. PM stops for 2 seconds, then 
DVR and WV energize, energizing PM and DV for 10 seconds. When the pump-out 
timer terminates, pump-out is complete. The pump-out frequency control is factory set 
for every 10th cycle, and generally no adjustment is required. However, where water 
quality is bad and the icemaker needs a pump-out more often, the pump-out frequency 
can be adjusted as shown in the table.

 

Timing of the first pump-out is dependent on S4 

dip switch 5 & 6 settings. See the table below.

S4 Dip Switch Setting

Pump-Out 

Frequency

1st Pump-Out

No. 5

No. 6

OFF

OFF

Every cycle

After 2nd freeze cycle

ON

OFF

Every 2 cycles

After 3rd freeze cycle

OFF

ON

Every 5 cycles

After 6th freeze cycle

ON

ON

Every 10 cycles

After 11th freeze cycle

Diagnosis:

 Confirm CB S4 dip switch 3 & 4 settings are in the factory default positions 

(3 off and 4 on). Check that Comp continues. Confirm WV and HGVs energize and LLVs 
de-energize. Next, check that DVR, PM, and DV energize. If DVR does not energize 
(LED 3 on), check CB #5 pin (DBu wire) on CB K1 ten-pin connector for 115VAC. If no 
voltage is present CB is bad and must be replaced. If 115VAC is present and DVR is not 
energized, check DVR solenoid for open windings. If DVR is energized and PM is not 
energized, check PM circuit (including DVR contacts), PM, and PM capacitor. If water 
is not going down the drain, check that DV is energized and open. If not, check that CB 
LEDs 4 and 3 are on and WV circuit energizes DV during pump-out. Check for 115VAC 
at DV solenoid and make sure DV is clear of debris. If water does not pump out, check 
and clean DV and tubing.   

7) 

Normal Harvest Cycle

 

–

 same as the initial harvest cycle – Return to "IV.A.4) Initial 

Harvest Cycle." 

8) 

Shutdown

Bin Control:

See "IV.C.1. Bin Control Check."

Legend: 

BC

–bin control; 

CB

–control board; 

Comp

–compressor; 

DV

–drain valve;          

DVR

–drain valve relay; 

FMRs

–fan motors-remote; 

F/S

–float switch; 

HGVs

–hot gas 

valves (KMS and SRK); 

HM

–headmaster (C.P.R.); 

LLVs

–liquid line valves (KMS 

and SRK); 

PM

–pump motor; 

TXV

–thermostatic expansion valve; 

WV

–inlet water 

valve

Содержание Serenity Series KMS-822MLH
















































Отзывы:

Нет отзывов