manualshive.com logo in svg

Hoshizaki Serenity Series KMS-822MLH, Руководство по обслуживанию, Страница: 36 / 47

Поделиться
Скачать
Hoshizaki Serenity Series KMS-822MLH Скачать руководство пользователя страница 36

36

Freeze Up - Possible Cause

6. Float Switch

See "IV.D. Float Switch Check 
and Cleaning"

a) Dirty, sticking.
b) Defective.

7. Refrigerant Charge

a) Low.

8. Control Board

See "II.C.2. Controls and 
Adjustments" and "IV.B. Control 
Board Check"

a) Harvest timer (S4 dip switch 1 & 2) set too short.
b) Harvest pump timer (S4 dip switch 3 & 4) not in factory default 

position.

c) Defective.

9. Bin Control

See "IV.C. Bin Control Check and 
Cleaning"

a) Actuator does not move freely.

10. Thermistor

See "IV.E. Thermistor Check"

a) Loose, disconnected, or defective.

11. Expansion Valve (TXV)

a) Defective.

12. Hot Gas Valves (KMS & SRK)

a) Closed.

13. Liquid Line Valves (KMS & SRK) a) Open.
14. Drain Valve Relay

a) Bad contacts. Open coil. Not allowing pump motor operation during 

last 50 seconds of harvest.

Freeze Cycle

1. Evaporator

a) Scaled up.
b) Damaged.

2. Spray Tubes and/or Spray 

Guides

a) Dirty.
b) Out of position.

3. Refrigerant charge

a) Low. 

4. Control Board

See "IV.B. Control Board Check"

a) Freeze timer set incorrectly.
b) Defective.

5. Inlet Water Valve

a) Leaking by.

6. Float Switch

See "IV.D. Float Switch Check 
and Cleaning"

a) Float does not move freely.
b) Defective.

7. Pump Motor

a) RPM too slow.

8. Expansion Valve (TXV)

a) Bulb loose or Defective.

9. Headmaster (C.P.R.)

a) Defective.

Содержание Serenity Series KMS-822MLH
















































Отзывы:

Нет отзывов