manualshive.com logo in svg

Hoshizaki KM-900MAH, Руководство по обслуживанию

Поделиться
Скачать
Hoshizaki KM-900MAH Скачать руководство пользователя страница 65

65

   Min. 4-3/4"

Liquid Bypass

        Flow

10) Secure the insulation using the Plastic Cable Ties.

11) Connect the Thermistor leads through the bushing of the Control Box to the K3

Connector on the Controller Board.

Note: Do not cut the leads of the Thermistor while installing it.

12) Replace the Control Box Cover and the panels in their correct positions.

13) Turn on the power supply.

12. REMOVAL AND REPLACEMENT OF FAN MOTOR

Note: When replacing a Fan Motor with defective winding, it is recommended
          that a new capacitor be installed.

1) Turn off the power supply.

2) Remove the panels.

3) Remove the Junction Box Cover from the remote condenser unit (Remote Air-cooled
     model).

4) Remove the closed end connectors from the Fan Motor leads.

5) Remove the Fan Motor Bracket and Fan Motor.

6) Install the new Fan Motor, and replace the removed parts in the reverse order of
    which they were removed.

7) Replace the panels in their correct positions.

8) Replace the Junction Box Cover in its correct position (Remote Air-cooled model).

9) Turn on the power supply.

Fig. 3

Содержание KM-900MAH










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды