manualshive.com logo in svg

Hoshizaki KM-900MAH, Руководство по обслуживанию

Поделиться
Скачать
Hoshizaki KM-900MAH Скачать руководство пользователя страница 50

50

  PROBLEM

         POSSIBLE CAUSE

 REMEDY

[4] Water

a) Water Solenoid

1. Diaphragm does not close.

1. Check for water leaks

     continues to

     Valve

     with icemaker off.

     be supplied in

b) Controller Board

1. Defective.

1. See “II.2.[e] CHECKING

     freeze cycle.

    CONTROLLER BOARD.”

[5] No water

a) Water Supply Line

1. Water pressure too low and

1. Check and get

     comes from

    water level in Water Tank

     recommended pressure.

    Spray Tubes.

    too low.

    Water Pump

b) Water Solenoid

1. Dirty mesh filter or orifice

1. Clean.

    will not start, or       Valve

    and water level in Water

    freeze cycle

    Tank too low.

    time is too           c) Water System

1. Water leaks.

1. Check connections for

    short.

     water leaks, and replace.

2. Clogged.

2. Clean.

d) Pump Motor

1. Motor winding opened.

1. Replace.

2. Bearing worn out.

2. Replace.

3. Wiring to Pump Motor.

3. Check for loose
    connection or open, and
    replace.

4. Defective Capacitor.

4. Replace.

5. Defective or bound impeller. 5. Replace and clean.
6. Mechanical Seal worn out.

6. Check and replace.

e) Controller Board

1. Defective.

1. See “II.2. [e] CHECKING
    CONTROLLER BOARD.”

[6] Fan Motor will

a) Fan Motor

1. Motor winding opened.

1. Replace.

     not start, or is

2. Bearing worn out.

2. Replace.

     not operating.

3. Wiring to Fan Motor.

3. Check for loose
    connection or open, and

               replace.

4. Defective Capacitor.

4. Replace

5. Fan blade bound.

5. Check and replace.

b) Controller Board

1. Defective.

1. See “II.2. [e] CHECKING
    CONTROLLER BOARD.”

[7] All components a) Refrigerant

1. Undercharged.

1. Check for leaks and

     run but no ice

     recharge.

     is produced.

2. Air or moisture trapped.

2. Replace Drier, and
    recharge.

b) Compressor

1. Defective valve.

1. Replace.

c) Hot Gas Solenoid

1. Continues to open in freeze

1. Check and replace.

    Valve

     cycle.

d) Line Valve

1. Continues to close in

1. Check and replace

     freeze cycle.

e) Water Supply Line

1. Condenser water pressure

1. Check and get

                        [Water-cooled model

    too low or off and Pressure

     recommended pressure.

    only]

    Control opens and closes

              frequently.

Содержание KM-900MAH










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды