manualshive.com logo in svg

Hoshizaki KM-900MAH, Руководство по обслуживанию

Поделиться
Скачать
Hoshizaki KM-900MAH Скачать руководство пользователя страница 4

4

IV.  SERVICE DIAGNOSIS ........................................................................................... 48

1.  NO ICE PRODUCTION........................................................................................ 48
2.  EVAPORATOR IS FROZEN UP .......................................................................... 51
3.  LOW ICE PRODUCTION ..................................................................................... 51
4.  ABNORMAL ICE .................................................................................................. 52
5.  OTHERS .............................................................................................................. 52

V.  REMOVAL AND REPLACEMENT OF COMPONENTS ........................................... 53

1.  SERVICE FOR REFRIGERANT LINES ............................................................... 53

[a] REFRIGERANT RECOVERY ......................................................................... 53
[b] EVACUATION AND RECHARGE [R-404A] ................................................... 53

2.  BRAZING ............................................................................................................. 54
3.  REMOVAL AND REPLACEMENT OF COMPRESSOR ....................................... 55
4.  REMOVAL AND REPLACEMENT OF DRIER ..................................................... 57
5.  REMOVAL AND REPLACEMENT OF EXPANSION VALVE ............................... 57
6.  REMOVAL AND REPLACEMENT OF HOT GAS VALVE AND ................................
      LINE VALVE ....................................................................................................... 58
7.  REMOVAL AND REPLACEMENT OF EVAPORATOR ........................................ 60
8.  REMOVAL AND REPLACEMENT OF WATER-REGULATING VALVE ...................
      - WATER COOLED MODEL ONLY .................................................................... 61
9.  ADJUSTMENT OF WATER-REGULATING VALVE .................................................
      - WATER COOLED MODEL ONLY .................................................................... 62

10.  REMOVAL AND REPLACEMENT OF CONDENSING PRESSURE .........................

       REGULATOR (C.P.R.)  - REMOTE AIR-COOLED MODEL ONLY ..................  63

11.  REMOVAL AND REPLACEMENT OF THERMISTOR.......................................... 64
12.  REMOVAL AND REPLACEMENT OF FAN MOTOR ........................................... 65
13.  REMOVAL AND REPLACEMENT OF WATER VALVE ........................................ 66
14.  REMOVAL AND REPLACEMENT OF PUMP MOTOR ........................................ 66
15.  REMOVAL AND REPLACEMENT OF SPRAY TUBES ........................................ 67

VI.  MAINTENANCE AND CLEANING INSTRUCTIONS ............................................... 68

1.  PREPARING THE ICEMAKER FOR LONG STORAGE ...................................... 68
2.  CLEANING ........................................................................................................... 70

[a] CLEANING PROCEDURE ............................................................................. 71
[b] SANITIZING PROCEDURE ........................................................................... 72

3.  MAINTENANCE ................................................................................................... 73

4.  PERFORMANCE DATA ....................................................................................... 43

[a] KM-900MAH (Air-cooled) ............................................................................... 43
[b] KM-900MWH (Water-cooled), Serial # L00001D-M20500D .......................... 44
[c] KM-900MWH (Water-cooled), Serial # M30501D--........................................ 45
[d] KM-900MRH (Remote air-cooled) ................................................................. 46
[e] KM-900MRH3 (Remote air-cooled 3 phase) .................................................. 47

Содержание KM-900MAH










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды