manualshive.com logo in svg

Hoshizaki KM-900MAH, Руководство по обслуживанию

Поделиться
Скачать
Hoshizaki KM-900MAH Скачать руководство пользователя страница 16

16

2. CONTROLLER BOARD

[a] SOLID-STATE CONTROL

1) A HOSHIZAKI exclusive solid-state control is employed in KM-900MAH,
    KM-900MWH, KM-900MRH and KM-900MRH3 Modular Crescent Cubers.

2) A Printed Circuit Board (hereafter called “Controller Board”) includes a stable and

high quality control system.

3) All models are pretested and factory-adjusted.

[b] CONTROLLER BOARD

CAUTION

1. Fragile, handle very carefully.

2. A controller board contains integrated circuits, which are susceptible to

failure due to static discharge.  It is especially important to touch the
metal part of the unit when handling or replacing the board.

3. Do not touch the electronic devices on the board or the back of the

board to prevent damage to the board.

4. Do not change wiring and connections.  Do not misconnect K3, K4 and

K5, because the same connector is used for the Thermistor (white),
Float Switch (black), and Mechanical Bin Control (red).

(For machines with thermostat, there is no connection on K4.)

5. Always replace the whole board assembly when it goes bad.

6. Do not short out power supply to test for voltage.

PART NUMBER

TYPE

2A1410-01                   HOS-001A (Control Products)

Features of Control Products “E” Controller Board

1) Maximum Water Supply Period - 6 minutes

Water Solenoid Valve opening, in the Defrost (Harvest) Cycle, is limited by the de-
frost timer.  The Water Valve cannot remain open longer than the maximum period.
The Water Valve can close in less than six minutes if the defrost cycle is completed.

Содержание KM-900MAH










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды