Hornet 553T Скачать руководство пользователя страница 53

Страница: 53 / 60

To enter or exit timer mode manually:

1. Make sure the remote start system is not operating the engine.

2. Turn the ignition on.

Timer Mode will be exited and the parking lights will flash four times.

table of zones

When using the Diagnostic functions, use the Table of Zones to see which input has triggered the system. It is

also helpful in deciding which input to use when connecting optional sensors and switches.

NOTE

: The Warn Away® response does not report on the LED.

shutdown diagnostics

1. With the ignition OFF, press and

HOLD

the Valet/Program button.

2. Turn the ignition ON and then back OFF while

HOLDING

the Valet/Program button.

3. Release the Valet/Program button.

4. Press and release the Valet/Program button. The LED will report the last shutdown for one minute or until

the ignition is turned on.

to perform shutdown diagnostics

ZONE NO.

TRIGGER TYPE

INPUT DESCRIPTION

Hood and/or Brake Trigger

GRAY and BROWN wires on the 6-pin shutdown harness.

Multiplexed Input

Heavy impact from the shock sensor.

Door Trigger

GREEN (H1/5) and VIOLET (H1/7).

Multiplexed Input

BLUE (H1/6)

Содержание 553T





























































Результаты поиска

Содержание 553T

Отзывы:

Похожие инструкции для 553T

Бренды по названию

Популярные бренды

Hornet 553T, Руководство по установке

Результаты поиска

Содержание 553T

Отзывы:

Похожие инструкции для 553T

Бренды по названию

Популярные бренды